Practice test · ASE B2 Auto Paint Exam Prep

Free ASE B2 Auto Paint Exam Prep Practice Test

Take a free ASE B2 Auto Paint Exam Prep practice test for 2026 with questions, answers, explanations, PDF download and timed mock exam links.

Free sample · ASE B2 Auto Paint Exam PrepQ1
Technician A says that an HVLP spray gun operates with air cap pressure of 10 PSI or less. Technician B says that HVLP spray guns have higher transfer efficiency than conventional spray guns. Who is right?
Correct — D. Both technicians are correct. HVLP (High Volume Low Pressure) spray guns operate with air cap pressure of 10 PSI or less, and they have higher transfer efficiency (65% or more) compared to conventional spray guns.
↑ Tap an answer to check it
Free questions

ASE B2 Auto Paint Exam Prep Questions

Open each answer, read the explanation, then continue into the full practice flow.

  1. Q1Technician A says that an HVLP spray gun operates with air cap pressure of 10 PSI or less. Technician B says that HVLP spray guns have higher transfer efficiency than conventional spray guns. Who is right?

    Show answer

    ✓ Correct answer: Both A and B

    Both technicians are correct. HVLP (High Volume Low Pressure) spray guns operate with air cap pressure of 10 PSI or less, and they have higher transfer efficiency (65% or more) compared to conventional spray guns.

    Open the full explanation page →

  2. Q2When spraying metallic basecoat, what happens if the air pressure is set too high?

    Show answer

    ✓ Correct answer: Mottling will occur

    When air pressure is set too high while spraying metallic basecoat, the metallic flakes can bounce back, causing mottling. This creates an uneven appearance where the metallic particles are distributed inconsistently.

    Open the full explanation page →

  3. Q3What is the primary purpose of the air cap on a spray gun?

    Show answer

    ✓ Correct answer: To direct compressed air into the fluid stream to atomize the paint

    The primary purpose of the air cap is to direct compressed air into the fluid stream to atomize the paint and shape the spray pattern. It's a critical component that affects the quality of atomization and pattern formation.

    Open the full explanation page →

  4. Q4Which of the following is NOT a typical adjustment on a spray gun?

    Show answer

    ✓ Correct answer: Viscosity adjustment

    A viscosity adjustment is not found on a spray gun. Viscosity is adjusted when mixing the paint, not on the gun itself. Spray guns typically have pattern control, air pressure, and fluid control adjustments.

    Open the full explanation page →

  5. Q5Technician A says that the fluid needle should be removed before cleaning the spray gun. Technician B says that the air cap should be removed before cleaning the spray gun. Who is right?

    Show answer

    ✓ Correct answer: Both A and B

    Both technicians are correct. For proper cleaning, both the fluid needle and air cap should be removed to allow thorough cleaning of all passages and components of the spray gun.

    Open the full explanation page →

  6. Q6What can happen if a spray gun's fluid tip and needle are mismatched?

    Show answer

    ✓ Correct answer: Improper atomization

    If the fluid tip and needle are mismatched, improper atomization will occur because these components are designed to work together as a set. Mismatching can lead to leaking, uneven spray patterns, and poor finish quality.

    Open the full explanation page →

  7. Q7When using infrared lamps to force-dry paint, which statement is TRUE?

    Show answer

    ✓ Correct answer: They heat the substrate, which then transfers heat to the paint film

    Infrared lamps heat the substrate directly, which then transfers heat to the paint film. This is more efficient than heating the air around the vehicle, as it focuses energy where it's needed most.

    Open the full explanation page →

  8. Q8What spray gun malfunction is indicated when paint is leaking around the fluid needle packing?

    Show answer

    ✓ Correct answer: The packing nut is too loose

    When paint is leaking around the fluid needle packing, the packing nut is likely too loose. The packing nut compresses the packing material to create a seal around the needle, and if it's loose, paint will leak through this area.

    Open the full explanation page →

  9. Q9What should be done to the spray pattern when painting a narrow area such as a door pillar?

    Show answer

    ✓ Correct answer: Adjust it to be narrow/vertical

    When painting narrow areas like door pillars, the spray pattern should be adjusted to be narrow/vertical to reduce overspray and ensure proper coverage of the targeted area without wasting material.

    Open the full explanation page →

  10. Q10Technician A says that UV lamps can be used to cure certain automotive coatings. Technician B says that UV curing typically takes longer than conventional curing methods. Who is right?

    Show answer

    ✓ Correct answer: A only

    Technician A is correct. UV lamps can be used to cure certain specialized automotive coatings. Technician B is incorrect because UV curing is actually faster than conventional methods, not slower.

    Open the full explanation page →

Unlock everything

Full ASE B2 Auto Paint Exam Prep bank + unlimited mocks

Try 30 questions free. Unlock the complete ASE B2 Auto Paint Exam Prep question bank, every explanation, and unlimited timed mock exams. Practice on any device.

Unlock ASE B2 Auto Paint Exam Prep →
Cramming?
$2.99
/ week · per exam
Best value
$6.99
/ month · per exam